Sound card disconnects when switching to CD or USB mode

Dj Usb Sound Card
Virtual Dj No Sound Card
Usb Sound Card For Pc
Best Gaming Usb Sound Card

Plug the USB Sound Card into an empty USB port and connect the headphones to the appropriate connector on the sound card. Select SPEAKER+HEADPHONE in the OUTPUT options and USB SOUNDCARD from the HARDWARE options. Once the Audio Setup is created select the multi-channel USB soundcard from the soundcard field instead. VirtualDJ will route Deck 1 to the 1st stereo channel and Deck 2 to the 2nd stereo channel of the multi-channel USB soundcard. Click APPLY to save these changes. The AUDIO tab is the most important part of your setup in Virtual DJ 8. This will determine your setup. Under AUDIO SETUP, make the following changes below. OUTPUT: Choose SPEAKER & HEADPHONE CARD: Choose your NUMARK CONTROLLER INPUT: Do not choose anything Note: Numark USB controllers without a sound card built in will have different setup.

Q. When I switch to CD or USB mode on my controller the sound in VirtualDJ stops working. How can I fix this?

If you have a media controller with a built-in sound card that can also play audio CD's or USB media then you may find that the sound card disconnects in VirtualDJ when switching into CD/USB mode. As a result, when you switch back to MIDI/HID/PC mode, you won't be able to play music in VirtualDJ due to the sound card configuration no-longer being valid.
This is because due to hardware/firmware design limitations of the controller, it de-activates the sound card and/or MIDI/HID driver when you switch to CD/USB mode. This is common on older and/or cheap controllers that don't have the capability to keep the USB driver active while in CD/USB mode.
This is equivalent to physically pulling out the USB cable, so as far as VirtualDJ is concerned, the controller and/or sound card has been disconnected and removed from the system. When you switch back to MIDI/HID/PC again, the driver will be re-activated. VirtualDJ supports plug and play of MIDI/HID devices, so the controller should start functioning again to control VirtualDJ once the MIDI/HID driver has reinitialised, however VirtualDJ does not currently support automatically re-activating a disconnected sound card when it becomes available again, so you will need to manually click APPLY in CONFIG -> Sound Setup, once your computer has finished detecting and initialising the driver again. Automatic plug and play re-activation of a sound card might be possible in a future version of the software.
If you need to be able to safely switch between CD/USB and VirtualDJ on the fly, then the best solution is to use a separate external DJ sound card (E.g: Numark DJIO) instead of the sound card built into media controller. The sound in VirtualDJ will then not be affected when you switch to CD/USB mode.
NOTE: If clicking APPLY in VirtualDJ doesn't work after switching back from CD to MIDI/HID/PC mode then this is a problem with the driver or WIndows hasn't detected that it's available again yet (It may take 10-30 seconds (Or longer) for your computer to recognise and configure/initialise its USB driver.) If it never re-initialises there may be a bug in the firmware.

FAQKnowledge DatabaseWiki HOME

DJ’ing, the shortened name of disc jockeying, is playing existing songs for an audience. DJs can be found at clubs, on the radio, at music festivals, and at various smaller live events like weddings and parties. The needs, wants, and skills of each DJ is different depending on the type of party, audience, and the DJ’s individual skill, so the setup used varies from DJ to DJ and could include old school setups like turntables and mixers or more modern setups like all-in-one devices or tablets. One of the most common setups, however, is the laptop and controller/mixer setup. Here is how you set up Laptop and Mixer.

Is it possible to DJ with a laptop and mixer?

Yes! One of the most common, portable, and versatile DJ setups is the laptop and mixer setup. All of your tracks can be stored in your laptop rather than on a stack of burned CDs, the laptop gives you the capability to easily beat-match and remix tons of hits, and depending on the size of your mixer/controller, if you’ve got a big enough backpack, you can take your entire setup with you practically anywhere with relative ease.

How can you DJ with a laptop and mixer?

To start DJing with a laptop and mixer, you’ll need some supplies:
1. Laptop of your choice
2. Charger for your laptop, as you’ll need to keep it plugged in
3. Mixer/controller of your choice
4. Power source for mixer/controller (if necessary, not all require an external power source)
5. Power conditioner
6. Surge protector
7. Headphones
8. DJing software

To get started with DJing on a laptop and mixer/controller setup, you first need to connect your devices so that they will work together. By looking at your devices, determine whether or not you’ll be using a separate USB cord to connect the devices or if you’ll be plugging your mixer/controller directly into your laptop.

If you’re using a separate USB cord to connect the two devices, plug one end into your laptop and the other into your mixer/controller. DO NOT use any kind of USB hub or splitter, only use a regular USB cord that connects directly from your laptop’s built in USB port to the mixer/controller. Using a USB hub or splitter will bottleneck the data traveling back and forth and will prevent it from transferring properly and/or quickly, especially if you end up chaining too many devices to one USB port – even more so if any of those devices are power-grabbing machines like DJ mixers and controllers. Also, when possible, use a USB 3.0 port rather than a 2.0 port, as 3.0 ports have a higher speed of transfer and transfer rate with a significantly lower chance of glitching than 2.0 ports.

Dj Usb Sound Card

If you’re not using a separate USB cord to connect the two machines, first make sure that your laptop and mixer/controller are compatible, as some mixers are only compatible with specific computers and operating systems. Once you’ve determined that they’re compatible, plug the device directly into your laptop’s built in USB port. DO NOT use any kind of USB hub or splitter, only use a regular USB cord that connects directly from your laptop’s built in USB port to the mixer/controller. Using a USB hub or splitter will bottleneck the data traveling back and forth and will prevent it from transferring properly and/or quickly, especially if you end up chaining too many devices to one USB port – even more so if any of those devices are power-grabbing machines like DJ mixers and controllers. Also, when possible, use a USB 3.0 port rather than a 2.0 port, as 3.0 ports have a higher speed of transfer and transfer rate with a significantly lower chance of glitching than 2.0 ports.

What do I do once my devices are connected?

Once you have your devices properly connected, open up your DJing software of choice. There are thousands of software options, but some favorites of other DJs include:

Ableton Live
Serato Scratch Live/DJ
Native Instruments Traktor Pro 2
Imagine-Line Deckadance
Magix Digital DJ 2
Mixvibes CrossDJ
Atomix VirtualDJ Pro 7
Pioneer Rekordbox

Virtual dj usb sound card setup download

Once in your DJing software of choice, go to the Audio Device tab. From there, select the device plugged into your USB port. From here, the directions vary based on whether or not your device has a built in sound card.

What do I do next if my device DOES have a built in sound card?

Virtual Dj No Sound Card

If your device has a built in sound card, go to System Preferences > Sound > Input > USB Audio Codec option > close System Preferences. From there, repeat the previous step again

Virtual Dj Usb Sound Card Setup